Guest jazzbell Posted August 1, 2014 Report Share Posted August 1, 2014 (edited) Classes for the 2015 Model Car Nationals will be the following....... NSR Classic Sideways group 5 NSR GT Slot-It Group C Open LMP/Proto under 14 Scalextric GT and Muscle cars Seniours Scalextric GT and Muscle Cars 1/24 scale Aussie slotworx V8'S 1/24 Scale LMP(endurance race)OAPR Open Australian Prototype Racing 1/32 Scale Plafit Div 1 Plafit MINI Z GT 1/24 Plafit can-am 1/24 Scaleauto All racing will be done on the Brabham 6 laner. The Scalextric magnet GTand muscle class will be raced on the 4 lane Lowndes track. 2015 Model Car Nationals Presented by Thunderbird racway Sth Australia. General rules and regulations. Cost per class to enter is $15. LMP 4Hr endurance race will be $90 per team and this will be a hand out motor for this event. Motor will be the EVO 25,000 Race Director for this event will be Gary Johnson from Queensland . Officals and Dutie: 1. The event organiser may appoint a Race director of acceptable knowlage and experience for each of the classes. 2. The Race Director may act as scrutineer and/or Race Controller or he/she may appoint an acceptable deputy to fill this positions. 3. The race director is responsible for all aspects of the running of racses in his/her charge. 4. The Scrutineer is responsable for ensuring that all cars conform to specifications for their class and relevant general rules. 5. The Race Controller is responsible for overseeing a particular race. Initiating Track Calls,directing marshalls,ect. Cars And Scrutineering: 1. Cars must comply with the specifications for their class and any relevant regulations at all times whilst racing. 2. Cars that do not conform to the relevant specifications shall be excluded from the event. 3. Cars must be submitted to the scrutineer prior or at the advertised time for the class. 4. Scrutinneers word is final. 5. The scrutineer is empowered to rule on any area of a cars construction not specifically coverd by the rules. 6. Cars will be scrutineered prior to each race/heat. 7. Cars can be scrutineered at any time or a teardown inspection at the descretion of the Race Director/Controller. Impounding Of Cars(PARK FERME): 1. The event organiser will provide a safe area where cars will be impounded. Typically they stay in park ferme after scrutineering until they are eliminated from the completion of racing. 2. Drivers may remove cars from PARK FERME prior to qualifying and must return the car back after they qualify to the PARK FERME . Like wise after racing cars have to be returned to PARK FERME. 3. All cars stay impounded until end of racing. Repairs and Parts Replacements: 1. All repairs and replacement components must comply with the specifications for the relevant class. 2. Any part may be replaced with the exception of the primary chassie section and the body shell. 3. All the repairs and parts replacements during the race event is subject to re scrutineering. DRIVER CONDUCT: 1. Drivers and their pit crew are expected to conduct themselves in a professional manner at all times. 2.Abusive,offensive or unsportmanlike conduct directed at any person will result in immediate penalties being aposed. 3. Driver are also cautioned that they might be held responsible for the actions of their pit crew. Smoking: In the interests of health and saftey,there will be stricly NO smoking in the racway. MARSHALLING 1. All entrants will marshall. 2. Entrants may nominate a substitute marshall. DUTIES of MARSHALS 1. Clear the track of de-slotted or malfunctioning cars. 2. Re place de slotted cars without interfering with the other cars. CONTROLLERS: 1. Any hand controller can be used as it does not increase the voltage or available amps to the track. DISPUTES and INTERPRETATION of the RULES. 1.The race Directors decision is bound and final,and their is no appeal on the decision. P PENALTIES: Any deliberate rule infraction contrived to gain a performance advantage will result in exclusion from the class. BLACK FLAG: 1.The race controller can demand the removal from the track of any car wich is dragging on the track,interfering with other cars,or continually de-slotting. 2.Any car that cannot complete a lap with out de-slotting will be black flagged. 3.Cars can be repaired and re enter the race. TRACK POWER SUPPLY: 1.Nominal track voltage for racing will be at 12 volts for all classes . 2.Depending on what class a higher voltage will be used .Race directors decision will be final on this. Edited March 26, 2015 by jazzbell 1 Link to comment Share on other sites More sharing options...
Guest jazzbell Posted August 1, 2014 Report Share Posted August 1, 2014 (edited) LMP/GT1 PROTO Open Rules: NOTE :EVEN THOUGH IT IS AN OPEN CLASS THE CAR MUST STILL LOOK LIKE A RTR 1/32 SCALE CAR . AXLES FRONT 1.Must be located in original,un-modified front axel holders. 2.Stabelizing of front end is allowed. 3.wheels must be inside the guards. AXLES REAR 1.Must be located in original un-modified rear axel holders. 2.Ball bearings are allowed. 3.wheels must be inside the guards. BODY: 1.NO sanding of wheel arches to allow for room for tyres to fit. 2.The body can NOT be modified in any way.Exception on the Nissan R90 where the gear hits on the air duct 3.Any screws can be used. 4.Any body that has a wing can have rubber added as struts to stop the wing from braking off. 5.Painted liveries are allowed making sure all parts are used. Race numbers in at least 3 places. CHASSIS: 1.Adding weight to any part of the chassis is allowed. 2.Reinforcing or gluing parts of the chassis such as axel bushings,motor mounting posts etc is allowed. 3. NO chassis magnets are allowed. 4. Must be plastic RTR chassis that comes with car. No metal chassis. GEARS: 1. OPEN Gear Ratio. GROUND CLEARANCE: 1. As long as day light can be seen. GUIDE: 1.Any Guide. 2.Any lead wire. 3.Any Braid. Interior: 1. Lexen can be used. MOTOR: 1. Long or Short can motors up to 30,000 RPM TYRES: 1. FOAM TYRES ONLY. NSR,SCALEAUTO OR SLOT.IT NO Tyre softening, conditioning or treating is allowed. Tyres cleaning with Shellite only. Some of the cars eligible for this class. AVANT SLOT: Peugeot 908 Porsche Spyder Audi Pescarolo LMP SLOTINGPLUS: Raynard 2KQ SCALEAUTO: RadicalSR-9 Toyota GT-1 SLOT.IT: Nissan R390 GT1 LOLA BO9/60S Audi R8C McLaren GTR NINCO: Acura. Audi R8 SCX: Audi R8 Audi R10 NSR: Audi R18 Audi R8 Scalextric: Porsche spyder Peugeot Lola Aston Martin 1-2 Audi R8 ____________________________________________________________________________________________________ Edited August 4, 2014 by jazzbell Link to comment Share on other sites More sharing options...
Guest jazzbell Posted August 1, 2014 Report Share Posted August 1, 2014 (edited) SCALEXTRIC GT MAGNET RULES (AMATEUR ONLY)Rules also apply for kids under 14 THIS IS A MAGNET RACED CLASS. MAXIMUM DOWNFORCE READING ON THE MAGNET MARSHALL WILL BE 350. NOTE YOU CAN ONLY RUN 1 MAGNET,BUT CHANGING OF MAGNET IS ALLOWED AS LONG AS IT FITS IN ORIGIANAL POSITION AND DOSNT EXCEED 350 DOWNFORCE. NO HIGH IMPACT CARS ALLOWED IN THIS CLASS. AXLES FRONT.(Front wheels can exceed.5 of a mm out side the guard on either side of original set up) 1. Original front Axel set up. 2.Must be located in original,unmodified front axle holders. 3.Side play may be adjusted by adding axle spacers. AXLES REAR.(Rear wheels can exceed .5 of a mm out side the guard on either side of original set up.) 1.Original rear axle and bushings only.NO BALL BEARINGS. 2.Must be located in the original ,unmodified rear axle holder. 3.Side play may adjusted by adding washers. Body. 1.Original unmodified Scalextric GT style bodies are allowed. 2.Rear wings must be mounted in original position before the start of a race.They also can be mounted with rubber supports to help prevent wings breaking off.Must remain in original position. 3.The windows must remain original and clear at all times. 4.The body must not be altered in any way and must have a .5mm ground clearance of the track surface. 5.Any screws may be used.Screws may be left loose. 6.Light shave of body is allowed to stop body catching on chassis. 7.Posts can be sleeved for more support and strenght to prevent breakages . 8.Painted liveries are allowed as long as all parts are used and 3 numbers are in place on the car. Chassis. 1.Only the original unmodified Scalextric GT style chassis is allowed. 2.Adding weight to any part of the chassis is allowed. 3.Gluing of bearings and gluing motor in is allowed. 4. Slight shave of the chassis is allowed to top from catching on the body. 5.Post holes can be opened up to stop screws catching. Gears. 1.Original plastic drive gear. 2.Original drive gear. Ground Clearance. 1. 0.5mm clearance under hole chassis. Guide. 1.Original guide. 2.Any lead wire. 3.Any braid. Interior. 1.Original unmodified interiors in place at all times. Motor. 1.Original Scalextric 18,000 rpm motors only. 2.The sealed motors can not be tampered with in any way. 3.Motors can be glued or taped in. 4.Resistors can be removed. 5.Lights can be removed or disconnected. Wheels/Tyres FRONT. 1.Original Scalextric only.Truing and gluing is allowed. 2.The front wheels must touch the flat surface when placed on the set up board. 3.Original rims only. Wheels/Tyres REAR. 1.Original Scalextric tyres and the only replacement is MJK. Gluing and truing is allowed. 2.Original rims only. 3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED. Tyre shore hardness may be checked against original packet standard tyres. Some of the eligible cars for this class. Aston Martin (NO pro performance car) Audi r8 LMS Dodge Viper Ferrari 330 Ferrari F430,F430 GT,F430GTR,and F430 GT2. Ford GT . Honda nsx Jaguar XKR,XKRS and GT3 Lamborghini Gallardo Maserati MC12 Maserati Cambiocorsa Mclaren MP4 12C Mclaren 722 GT Mercedes SLR Mercedes GT1 Lemans Nissan GT-R Nissan Skyline Nissan 350Z Porsche GTR3 Porsche 997 GT3/ with exception of the flying Lizard which has a 20,000rpm motor. Toyota Supra __________________________________________________________________________________________________________ Edited August 2, 2014 by jazzbell Link to comment Share on other sites More sharing options...
Guest jazzbell Posted August 1, 2014 Report Share Posted August 1, 2014 SLOT IT GROUP C RULES. AXLE FRONT: 1. Original front axle. 2. Must be located in the original,unmodified front axle holders. 3. Side play may be adjusted by adding axle washers. 4.wheels must be inside the guards. AXLE REAR: 1.Original rear axle bushings only,NO ball bearings. 2. Must be located in original,unmodified rear axle holders. 3. Side play may be adjusted by adding axle washers. 4.wheels must be on the inside of the guards. BODY: 1.Only the original unmodified Slot.It group C in-line chassis is allowed. 2.Rear wings must be mounted on the body in the original position before the start of the race.Rubber supports can be added to prevent wings from breaking off.Must be in original position. 3.If the rear wing comes detached during the race,it must be re attached before the next bracket. 4.The windows must remain original and in place at all times. 5.The body must not be altered in any way. 6. All the body screws must be in place.Any screws may be used. 7. The rear spats can be removed on the XJ9 and XJ12 Jaguar. 8. Painted liveries are allowed making sure all the parts are used and numbers have to be in at least 3 places on the car. Legal bodies....... Mercedes Sauber C9 Mazda 787 B Lancia LC 2 jaguar XJ9 and XJ12 Porsche 956 KH Porsche 962 C Porsche 956 C Toyota 88 C Nissan R89C CHASSIS: 1.Only the original unmodified Slot.It group C chassis is allowed. 2. Adding weight to any part of the chassis is allowed. 3. Reinforcing or gluing parts of the chassis such as axle bushings,motor mounting post is allowed. 4. NO MAGNETS. 5. Opening screw holes to stop screws from catching is aloud. 6. Light scrape is aloud of chassis to stop body catching GEARS: 1.Original Slot.It YELLOW 28T crown in-line gear. 2.Original Slot.It 9T pinion. GROUND CLEARANCE: 1. Day light must be seen. GUIDE: 1.Any Slot.It replacement guide. 2.Any lead wire. 3.Any braid. INTERIOR: 1.Original unmodified interiors must be in place at all times. MOTOR: 1.Original unmodified 21,500rpm slot.it group C motors only. 2.The motor tabs holding the end bell must not be tampered with in any way,otherwise it will be disqualified. 3.Cars that came with the 25,000rpm motor can change them to a 21,500rpm motor. WHEELS/TYRES FRONT:(NO SILICON TYRES.) 1.Only original slot.it group C tyres are permitted. 2.Sanding gluing and truing is allowed. 3.Tyres must touch on set up board when checked. 4.Original rims only. WHEELS/TYRES REAR:(NO SILICONS TYRES.) 1.FOAM TYRES ONLY. SLOT IT foam to suit slot it wheels part number WH1211-AL OR WH1190-AL/NSR PART NUMBERS 9024 AND 9025/SCALEAUTO SC-2009P 2.Sanding gluing and truing is allowed. 3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED. Link to comment Share on other sites More sharing options...
Guest jazzbell Posted August 1, 2014 Report Share Posted August 1, 2014 (edited) NSR Classic AXLES FRONT: 1.Original front axle. 2.Must be located in original,un-modified front axle holders. 3.Side play may be adjusted by adding axle washers. 4.wheels must be inside the guards. AXLES REAR: 1.Original rear axle bushings only. 2.Must be located in the original,un-modified rear axle holders. 3.NO BALL BEARINGS. 4.wheels must be inside the guards. BODY: 1.NSR Classic body only. 2.Painted liveries are allowed.Numbers have to be in at least places on the body. 3.Srew posts can be sleeved for extra support to prevent breakages. 4.If the car comes with the dummy spare wheel it must remain in the car as it come. CHASSIS: 1.Only the NSR classic chassis for the make of car be used(Porsche to Porsche etc.) 2.Adding weight to any part of the chassis is allowed. 3.Reinforcing or gluing parts of the chassis such as axle bushings,motor mounting posts ect is allowed. 4.No chassis magnets are allowed. GEARS: 1.NSR GEARS ONLY.Gear ratio is 11/32. GROUND CLEARANCE: 1.Day light must be seen. GUIDE: 1.Any wood track guide. INTERIOR: 1.Original un-modified interiors must be in place at all times. MOTOR: 1.Un modified small can shark 20,000rpm motors only(comes standard in all nsr classic cars). 2.Side winder set up only. 3.The motor may be glued or taped in. 4.The motor tabs must remain intac,any tampering will result in diqualification. 5.Motor lables must be intact.Orange 20,000rpm. WHEELS/TYRES FRONT:(NO Silicon) 1.Any front tyre. 2.Sanding/truing tyre is permitted. 3.tyres must touch the track surface.(allowance will be made as these cars released the fronts do not always touch the set up board.) 4.Original rims only. WHEELS/TYRES REAR: (NO Silicon) 1.FOAM TYRES ONLY....NSR PART NUMBERS 9024 AND 9025/SLOT IT/SCALEAUTO SC-2009P 2.Sanding/Gluing and truing is allowed. 3.TYRE TREATING, SOFTENING OR CONDITION OF ANY KIND IS NOT ALLOWED. 4.Cleaning with shellite ONLY is allowed. Edited August 4, 2014 by jazzbell Link to comment Share on other sites More sharing options...
Guest jazzbell Posted August 2, 2014 Report Share Posted August 2, 2014 (edited) NSR GT AXLES FRONT: 1.Original front axle. 2.Must be located in original,un-modified front axle holders. 3.Side play may be adjusted by adding axle washers. 4.wheels must be inside the Guards. AXLES REAR: 1.Original rear axle bushings only. 2.Must be located in the original,un-modified rear axle holders. 3.NO BALL BEARINGS. 4.wheels must be inside the Guards. BODY: 1.NSR GT body only. 2.Painted liveries are allowed.Numbers have to be in at least places on the body. 3.Srew posts can be sleeved for extra support to prevent breakages. CHASSIS: 1.Only the NSR GT chassis for the make of car CAN be used(Porsche to Porsche etc.) 2.Adding weight to any part of the chassis is allowed. 3.Reinforcing or gluing parts of the chassis such as axle bushings,motor mounting posts ect is allowed. 4.No chassis magnets are allowed. 5.Opening srew holes up to allow srews from catching when mounting body is aloud. 6.Light shave of chassis is aloud to stop body catching. GEARS: 1.NSR GEARS ONLY.Gear ratio is 13/31. GROUND CLEARANCE: 1.Day light must be seen. GUIDE: 1.Any wood track guide. INTERIOR: 1.Original un-modified interiors must be in place at all times. MOTOR: 1.Un modified kink 21,400rpm motors only(comes standard in all nsr GT cars). 2.Angle winder set up only. 3.The motor may be glued or taped in. 4.The motor tabs must remain intac,any tampering will result in diqualification. 5.Motor lables must be intact.Orange 21,400rpm. or pink 21,400rpm. Early model gt cars came out with a Orange label part number nsr3017 and the later models have a pink label part number Nsr3023. Both these motors can be used in this event. THE ORANGE LABEL HAS A 320g.cm and the later PINK LABEL is rated at 350g.cm WHEELS/TYRES FRONT:(NO Silicon) 1.Any front tyre. 2.Sanding/truing tyre is permitted. 3.tyres must touch the track surface. 4.Original rims only. WHEELS/TYRES REAR: (NO Silicon) 1.FOAM TYRES ONLY....NSR PART NUMBERS 9024 AND 9025/SLOT IT/SCALEAUTO SC-2009P 2.Sanding/Gluing and truing is allowed. 3.TYRE TREATING, SOFTENING OR CONDITION OF ANY KIND IS NOT ALLOWED. 4.Cleaning with shellite ONLY is allowed. NSR GT car list Porsche 997 Audi R8 LMS Corvette CR6 Aston Martin gtr GT3 Edited August 4, 2014 by jazzbell Link to comment Share on other sites More sharing options...
Guest jazzbell Posted August 2, 2014 Report Share Posted August 2, 2014 (edited) Sideways GROUP 5 RULES. AXLE FRONT: 1. Original front axle. 2. Must be located in the original,unmodified front axle holders. 3. Side play may be adjusted by adding axle washers. 4.wheels must be inside the guards. AXLE REAR: 1.Original rear axle bushings only,NO ball bearings. 2. The offset axel holders can replace the standard that come in the car as these parts are with the car as spare options. 3. Side play may be adjusted by adding axle washers. 4.wheels must be inside the guards. BODY: 1.Only the original unmodified Group 5 angel winder chassis is allowed. 2.Rear wings must be mounted on the body in the original position before the start of the race.Rubber supports can be added to prevent wings from breaking off.Must be in original position. 3.If the rear wing comes detached during the race,it must be re attached before the next bracket. 4.The windows must remain original and in place at all times. 5.The body must not be altered in any way.Light scrape is aloud to stop body catching on chassis. 6. All the body screws must be in place.Any screws may be used. 7. Painted liveries are allowed making sure all the parts are used and numbers have to be in at least 3 places on the car. CHASSIS: 1.Only the original unmodified sideways group 5 anglewinder chassis is allowed. 2. Adding weight to any part of the chassis is allowed. 3. Reinforcing or gluing parts of the chassis such as axle bushings,motor mounting post is allowed. 4. NO MAGNETS. 5. Opening screw holes to stop screws from catching is aloud. 6. Light scrape is aloud of chassis to stop body catching GEARS: 1.Original Slot.It YELLOW 28T anglewinder gear. 2.Original Slot.It 11T pinion. GROUND CLEARANCE: 1. Day light must be seen. GUIDE: 1.Any Slot.It replacement guide. 2.Any lead wire. 3.Any braid. INTERIOR: 1.Original unmodified interiors must be in place at all times. MOTOR: 1.Original unmodified 20,500rpm slot.it motors only. They are Slot-it motors that are released in sideways cars. 2.The motor wrapper has to be in tact,otherwise it will be disqualified. 3. Note the first lot of Capri cars were released with a open can both sides .These motors a still rated with the same everthing to what comes in the sideways cars to date. Anyone wishing to replace a motor can use the 20,500rpm Slot-it motor part number MN0O9CH. Motor label must be on. WHEELS/TYRES FRONT:(NO SILICON TYRES.) 1.Only original slot.it tyres are permitted. 2.Sanding gluing and truing is allowed. 3.Tyres must touch on set up board when checked. 4.Original rims only. WHEELS/TYRES REAR:(NO SILICONS TYRES.) 1.FOAM TYRES ONLY. SLOT IT/NSR PART NUMBERS 9024 AND 9025/SCALEAUTO SC-2009P 2.Sanding gluing and truing is allowed. 3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED. Ford Capri Porsche 935/78 BMW M1 LANCIA BETA MONTECARLO Ferrari 512BB Group 5 Edited August 7, 2014 by jazzbell Link to comment Share on other sites More sharing options...
Guest jazzbell Posted August 2, 2014 Report Share Posted August 2, 2014 SCALEXTRIC MUSCLE CAR MAGNET RULES (AMATEUR ONLY)Rules also apply for kids under 14 THIS IS A MAGNET RACED CLASS. MAXIMUM DOWNFORCE READING ON THE MAGNET MARSHALL WILL BE 350. NOTE YOU CAN ONLY RUN 1 MAGNET,BUT CHANGING OF MAGNET IS ALLOWED AS LONG AS IT FITS IN ORIGIANAL POSITION AND DOSNT EXCEED 350 DOWNFORCE. NO HIGH IMPACT CARS ALLOWED IN THIS CLASS. AXLES FRONT.(Front wheels can exceed.5 of a mm out side the guard on either side of original set up) 1. Original front Axel set up. 2.Must be located in original,unmodified front axle holders. 3.Side play may be adjusted by adding axle spacers. AXLES REAR.(Rear wheels can exceed .5 of a mm out side the guard on either side of original set up.) 1.Original rear axle and bushings only.NO BALL BEARINGS. 2.Must be located in the original ,unmodified rear axle holder. 3.Side play may adjusted by adding washers. Body. 1.Original unmodified Scalextric GT style bodies are allowed. 2. 3.The windows must remain original and clear at all times. 4.The body must not be altered in any way and must have a .5mm ground clearance off the track surface. 5.Any screws may be used.Screws may be left loose. 6.Light shave of body is allowed to stop body catching on chassis. 7.Posts can be sleeved for more support and strenght to prevent breakages . 8.Painted liveries are allowed as long as all parts are used and 3 numbers are in place on the car. Chassis. 1.Only the original unmodified Scalextric GT style chassis is allowed. 2.Adding weight to any part of the chassis is allowed. 3.Gluing of bearings and gluing motor in is allowed. 4. Slight shave of the chassis is allowed to top from catching on the body. 5.Post holes can be opened up to stop screws catching. Gears. 1.Original plastic drive gear. 2.Original drive gear. Ground Clearance. 1. 0.5mm clearance under hole chassis. Guide. 1.Original guide. 2.Any lead wire. 3.Any braid. Interior. 1.Original unmodified interiors in place at all times. Motor. 1.Original Scalextric 18,000 rpm motors only. 2.The sealed motors can not be tampered with in any way. 3.Motors can be glued or taped in. 4.Resistors can be removed. 5.Lights can be removed or disconnected. Wheels/Tyres FRONT. 1.Original Scalextric only.Truing and gluing is allowed. 2.The front wheels must touch the flat surface when placed on the set up board. 3.Original rims only. Wheels/Tyres REAR. 1.Original Scalextric tyres and the only replacement is MJK. Gluing and truing is allowed. 2.Original rims only. 3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED. Tyre shore hardness may be checked against original packet standard tyres. Car list Dodge Charger Daytona 1969 Chev Camaro 1969 or 70 Ford Mustang 1969 Dodge Challenger1970 Mercuy Cougar XR7 Ford Falcon xb Coup Corvette Stingray L88 1969 Link to comment Share on other sites More sharing options...
Recommended Posts